Components
427 components matching “SPEED”
A component is a schematic symbol with, where the catalog has them, its footprint and 3D package model — linked by KiCad's own references and cross-checked pin by pin.
PE29101
Driver_FET
UltraCMOS High-Speed FET Driver, 40 MHz, Output Current 2.0A/4.0A, 80V, Half Bridge, Low Side Output, CSP-16
- Pins
- 16
- Pads
- 16
- SMD
- 2.1×2.5
PE29102
Driver_FET
UltraCMOS High-Speed FET Driver, 40 MHz, Output Current 2.0A/4.0A, 80V, Half Bridge, Phase Control, CSP-16
- Pins
- 16
- Pads
- 16
- SMD
- 2.1×2.5
UCC27524DGN
Driver_FET
Dual 5A MOSFET driver, 4.5V..18V supply, non-inverting, HTSSOP-8 (MSOP-8)
- Pins
- 9
- Pads
- 9
- SMD
- 6.4×3.5
TS3USB221RSER
gekkio-Gekkio_Interface_USB
High-Speed USB 2.0 1:2 Multiplexer/Demultiplexer Switch with Single Enable, UQFN-10
- Pins
- 10
- Pads
- 10
- SMD
- 2.4×2.9
SIT1057TK-3
Interface_CAN_LIN
CAN-FD Transceiver, 5Mbps, 5V supply, I/O compatible with 3.3V (VIO supply), high-speed / silent mode pin, WSON-8 / DFN-8
- Pins
- 9
- Pads
- 9
- SMD
- 4.3×3.5
TJA1043TK
Interface_CAN_LIN
High-speed CAN-FD Transceiver with Sleep Mode, HVSON-14
- Pins
- 15
- Pads
- 15
- SMD
- 4.4×5.0
TJA1049TK
Interface_CAN_LIN
High-Speed CAN Transceiver, standby mode, VSON-8 (DFN-8)
- Pins
- 9
- Pads
- 9
- SMD
- 4.3×3.5
TJA1049TK-3
Interface_CAN_LIN
High-Speed CAN Transceiver, separate VIO, standby mode, VSON-8 (DFN-8)
- Pins
- 9
- Pads
- 9
- SMD
- 4.3×3.5
TJA1145TK
Interface_CAN_LIN
High-speed CAN transceiver for partial networking, DFN-14
- Pins
- 15
- Pads
- 15
- SMD
- 4.4×5.0
TJA1145TK-FD
Interface_CAN_LIN
High-speed CAN transceiver for partial networking with FD-passive function, DFN-14
- Pins
- 15
- Pads
- 15
- SMD
- 4.4×5.0
LAN7500-ABJZ
Interface_Ethernet
Hi-Speed USB 2.0 to 10/100/1000 Ethernet Controller, QFN-56
- Pins
- 57
- Pads
- 57
- SMD
- 9.3×9.3
STR485
Interface_UART
RS-485, RS-422, half duplex transceiver, selectable speed 250 kbps or up to 20 Mbps, DFN-10 (VSON-10)
- Pins
- 11
- Pads
- 11
- SMD
- 4.3×3.6
BQ24392
Interface_USB
Dual SPST USB 2.0 High Speed Switch with USB Battery Charging Specification Revision 1.2 Detection, UQFN-10
- Pins
- 10
- Pads
- 10
- SMD
- 2.4×2.9
FT234XD
Interface_USB
Full Speed USB to Basic UART, WDFN-12
- Pins
- 13
- Pads
- 13
- SMD
- 4.2×3.5
STULPI01A
Interface_USB
High-speed USB On-The-Go ULPI transceiver
- Pins
- 36
- Pads
- 36
- SMD
- 5.6×5.6
STULPI01B
Interface_USB
High-speed USB On-The-Go ULPI transceiver
- Pins
- 36
- Pads
- 36
- SMD
- 5.6×5.6
USB3250-ABZJ
Interface_USB
Hi-Speed USB Device Transceiver with UTMI Interface, QFN-56
- Pins
- 57
- Pads
- 57
- SMD
- 9.3×9.3
C8051F321-GM
MCU_SiliconLabs
16 KB ISP FLASH MCU Family with Full Speed USB, 2304 bytes internal RAM, 21 port I/O, 10-bit ADC, built-in temperature sensor, fully compatible with MCS-51 instruction set, QFN-28
- Pins
- 29
- Pads
- 29
- SMD
- 6.2×6.2
CH32X035G8U6
MCU_WCH_RiscV
48MHz RISC-V MCU with USB PD phy (Sink, Source, DRP), USB 2.0 Full speed phy (Host, Device), 20KB RAM, 62KB Flash, WQFN-28
- Pins
- 29
- Pads
- 29
- SMD
- 5.3×5.3
M95512-Axxx-MF
Memory_EEPROM
Automotive 512-Kbit serial SPI bus EEPROMs with high-speed clock, DFN-8
- Pins
- 9
- Pads
- 9
- SMD
- 4.3×2.5
IS6xC1024AL-xxJ
Memory_RAM
128K x 8-bit High-Speed CMOS Static RAM, IS61C1024AL (commercial and industrial) / IS64C1024AL (automotive), VDD = 5V ±10%, 12/15ns, SOJ-32 (300 mil)
- Pins
- 32
- Pads
- 32
- SMD
- 9.8×21.5
IS6xC1024AL-xxK
Memory_RAM
128K x 8-bit High-Speed CMOS Static RAM, IS61C1024AL (commercial and industrial) / IS64C1024AL (automotive), VDD = 5V ±10%, 12/15ns, SOJ-32 (400 mil)
- Pins
- 32
- Pads
- 32
- SMD
- 12.6×21.5
TBU-CA025-050-WH
Power_Protection
low capacitance single bidirectional high-speed protection, 250V 50mA 13.3ohm, https://www.bourns.com/data/global/pdfs/TBU-CA.pdf
- Pins
- 3
- Pads
- 3
- SMD
- 7.0×4.5
TBU-CA025-100-WH
Power_Protection
low capacitance single bidirectional high-speed protection, 250V 100mA 7.1ohm, https://www.bourns.com/data/global/pdfs/TBU-CA.pdf
- Pins
- 3
- Pads
- 3
- SMD
- 7.0×4.5